View SKY66109-11-15_8646129.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

skyworks solutions, inc. ? phone [ 781] 376-3000 ? fax [781] 376-3100 ? sales@ skyworksinc.com ? www.skyworksinc.com 203034f ? skyworks proprietary information ? products and product in formation are subject to cha nge without notice ? aug ust 13, 2015 1 data sheet sky66109-11: 2.4 ghz zigbee ? /smart energy front-end module applications ? smart meters ? in-home appliances ? smart thermostats features ? integrated pa with up to +22.5 dbm output power ? integrated lna with programmable bypass ? integrated antenna switching with transmit and receive diversity function ? low noise figure: 2 db typical ? differential transmit/receive interface with integrated baluns ? fast switch on/off time: <800 ns ? supply range: 2.0 v to 3.6 v ? sleep mode current: 0.05 a typical ? no bias resistor is required ? small mcm (20-pin, 3 x 4 x 0.9 mm) package, nipdau-plated (msl3, 240 c per jedec-j-std-020) s kywork s green tm product s are compliant with all applicable legi s lation and are halogen-free. for additional information, refer to skyworks de?ition of green tm , document number s q04C0074. y0306 1 g nd txp txn v b_out rxp rxn v b_in g nd g nd ant2 ctx vcc1 cps csd vcc2 g nd ant_sel ant1 g nd 2 3 4 5 6 14 15 16 13 12 11 20 19 18 17 8910 7 g nd figure 2. sky66109-11 pinout (top view) pa lna balun rxp rxn logic control txp txn ant1 ant2 vb_out v b_in c p s c tx cs d ant_ s el balun s 2 6 5 9 figure 1. sky66109-11 functional block diagram description the sky66109-11 is a high-performance, fully integrated rf front-end module (fem) designed for zigbee?/smart energy applications. the sky66109-11 is designed for ease of use and maximum flexibility. the device provides integrated and fully matched input baluns, an integrated interstage matching and harmonic filter, and digital controls compatible with 1.6 to 3.6 v cmos levels. the rf blocks operate over a wide supply voltage range from 2.0 v to 3.6 v that allows the sky66109-11 to be used in battery powered applications over a wide spectrum of the battery discharge curve. the sky66109-11 is provided in a small, 20-pin, 3 x 4 mm multi- chip module (mcm) package. a functional block diagram is shown in figure 1. the pin configuration and package are shown in figure 2. signal pin assignments and functional pin descriptions are provided in table 1.
data sheet ? sky66109-11: zigbee/smart energy fem skyworks solutions, inc. ? phone [ 781] 376-3000 ? fax [781] 376-3100 ? sales@ skyworksinc.com ? www.skyworksinc.com 2 august 13, 2015 ? skyworks prop rietary information ? products and product information are s ubject to change without notic e ? 203034f table 1. sky66109-11 signal descriptions pin name description pin name description 1 g nd g round 11 g nd g round 2 txp positive transmit input signal from transceiver, 200 differential 12 ant1 connect to 50 antenna 3 txn negative transmit input signal from transceiver, 200 differential 13 g nd g round 4 vb_out transmit balun bias core supply from transceiver (optional connection) 14 ant_sel connect to g pio signal to control antenna switch (see table 7) 5 rxp positive receiver output signal to transceiver, 200 differential 15 g nd g round 6 rxn negative receiver output signal to transceiver, 200 differential 16 vcc2 connect to positive supply 7 vb_in receive balun bias core supply from transceiver (optional connection) 17 csd connect to g pio signal for mode control (see table 6) 8 g nd g round 18 cps connect to g pio signal for mode control (see table 6) 9 g nd g round 19 vcc1 connect to positive supply 10 ant2 connect to 50 antenna 20 ctx connect to g pio signal for mode control (see table 6) the balun at the fem pa input (or lna output) can al s o be u s ed to inject a bia s operating point for the tran s ceiver output s tage (the s hunt inductor provide s a d c path on the other s ide). the inductor al s o tune s out any para s itic capacitance. if the s oi c tran s ceiver doe s not require a d c bia s , leave the vb_in open. c p s cs d c tx fem s o c vdd_pa vb_out 1 pf 1 pf 2n7 1 k each s erie s re s i s tor, placed clo s e to the s ky 66 10 9 pin s . optional output filter y22 6 1 differential s ource or load impedance s ymbol input input 1.8 v v bia s _in 1.8 v 1.8 v decoupling capacitor on chip internal lattice balun vb_in vreg_out +1.8 v figure 3. injecting a bias operating point for the transceiver output stage
data sheet ? sky66109-11: zigbee/smart energy fem skyworks solutions, inc. ? phone [ 781] 376-3000 ? fax [781] 376-3100 ? sales@ skyworksinc.com ? www.skyworksinc.com 203034f ? skyworks proprietary information ? products and product in formation are subject to cha nge without notice ? aug ust 13, 2015 3 electrical and mechanical specifications the absolute maximum ratings of the sky66109-11 are provided in table 2. the recommended operating conditions are specified in table 3 and electrical specifications are provided in tables 4 and 5. the state of the sky66109-11 is determined by the logic provided in tables 6 and 7. table 2. sky66109-11 absolute maximum ratings (note 1) parameter symbol minimum maximum units supply voltage v cc 1 C0.3 +3.6 v supply voltage v cc 2 C0.3 +3.8 (note 2) v control pin voltages C0.3 +3.6 v transmit output power at ant1 or ant2 port into 50 load p out _ tx _ max +22.5 dbm transmit input power at the txn and txp ports p in _ tx _ max +6 dbm receive input power at ant1 or ant2 ports, lna mode p in _ rx _ max +10 dbm receive input power at ant1 or ant2 ports, bypass mode p in _ rx _ bypass _ max +15 dbm operating temperature t a C40 +125 ? c storage temperature t st g C40 +125 ? c electrostatic discharge: human body model (hbm), class 1c esd 1000 v note 1: exposure to maximum rating conditions for extended periods may reduce device reliability. there is no damage to device with on ly one parameter set at the limit and all other parameters set at or below their nominal value. exceeding any of the limits listed here may result in permanent damage to the d evice. note 2: vcc 2 is restricted to +3.6 v when operated at t a = 125 ? c. caution : although this device is designed to be as robust as possible, electrostatic discharge (esd) can damage this device. this devi ce must be protected at all times from esd. static charges may eas ily produce potentials of several kilovolts on the human body or equipment, which can discharge without detection. industry-standard esd precautions should be used at all times. table 3. recommended operating conditions parameter symbol minimum typical maximum units supply voltage for balun bias vb_in, vb_out 1.6 3.6 v supply voltage on vcc pins vcc1, vcc2 2.0 3.0 3.6 v operating temperature t a C40 +25 +125 ? c
data sheet ? sky66109-11: zigbee/smart energy fem skyworks solutions, inc. ? phone [ 781] 376-3000 ? fax [781] 376-3100 ? sales@ skyworksinc.com ? www.skyworksinc.com 4 august 13, 2015 ? skyworks prop rietary information ? products and product information are s ubject to change without notic e ? 203034f table 4. sky66109-11 electrical specifications (note 1) (vcc1 = vcc2 = 3.0 v, t a = +25 ? c, unless otherwise noted) parameter symbol test condition min typical max units dc characteristics total supply current i cc _ tx p out = +20 dbm p out = +17 dbm (note 2) p out = +10 dbm (note 2) 110 90 45 ma ma ma total supply current i cc _ rx 5 7 ma total supply current i cc _ rx _ bypass 300 a sleep supply current i cc _ off no rf 0.05 1.00 a quiescent current icq no rf 30 ma logic characteristics control voltage: high low v ih v il 1.6 0 3.6 0.3 v v control current: high low i ih i il 1 1 a a dual antenna switch characteristics isolation between ant1 and ant2 ports isol antsw C20 db ant1 to ant2 switching time t ant 1_ ant 2 400 ns note 1: performance is guaranteed only under the conditions listed in this table. note 2: not tested in production. fully characterized and guaranteed by design.
data sheet ? sky66109-11: zigbee/smart energy fem skyworks solutions, inc. ? phone [ 781] 376-3000 ? fax [781] 376-3100 ? sales@ skyworksinc.com ? www.skyworksinc.com 203034f ? skyworks proprietary information ? products and product in formation are subject to cha nge without notice ? aug ust 13, 2015 5 table 5. sky66109-11 electrical specifications (note 1) (vb_in = vb_out = 1.6 to 3.6 v, vcc1 = vcc2 = 3.0 v, t a = +25 ? c, all unused ports terminated with 50 , unless otherwise noted) parameter symbol test condition min typical max units ac transmit characteristics frequency range f 2400 2483 mhz output power at ant1 or ant2 port p out vcc1 = vcc2 =: 3.6 v 3.3 v 3.0 v 2.7 v 2.0 v +22.5 +21.0 +20.5 +20.0 +17.0 dbm dbm dbm dbm dbm small signal gain s 21 p in = C25 dbm 21 db small signal gain variation s 21 across all zigbee channels 2 dbp-p saturated gain g _ sat p out = +20 dbm 17 19 db 2 nd harmonic 2fo p out = +20 dbm, ieee 802.15.4 source C42 dbm/mhz 3 rd harmonic (note 2) 3fo p out = +20 dbm, ieee 802.15.4 source C42 dbm/mhz output return loss (note 2) s 22 ant1 or ant2 port C10 C5 db transmit port impedance (note 2) z in 200 turn-on time (note 2) t rise from 50% of ctx edge to 90% of final rf output power 800 ns turn-off time (note 2) t fall from 50% of ctx edge to 10% of final rf output power 800 ns stability (note 2) stab cw, pin = 0 dbm, 0.1 g hz to 20 g hz, load vswr = 6:1 all non-harmonically related outputs < C42 dbm/mhz C ruggedness (note 2) ru cw, pin = +6 dbm, load vswr = 10:1 no permanent damage C ac receive characteristics frequency range f 2400 2483 mhz receive gain rx _ g ain 10.5 db receive noise figure (note 2) nf 2 db third order input intercept point (note 2) iip3 C3 +1 dbm 1 db input compression point ip1db C13 C3 dbm 1 db input compression point in bypass mode (note 2) ip1db +10 dbm input return loss (note 2) s 11 ant1 or ant2 ports C10 C5 dbm receive port impedance (note 2) z out measured differentially between rxp and rxn 200 turn-on time (note 2) t rise from 50% of ctx edge to 90% of final rf output power 800 ns turn-off time (note 2) t fall from 50% of ctx edge to 10% of final rf output power 800 ns g ain in bypass mode g _ bp C3 db note 1: performance is guaranteed only under the conditions listed in this table. note 2: not tested in production. fully characterized and guaranteed by design.
data sheet ? sky66109-11: zigbee/smart energy fem skyworks solutions, inc. ? phone [ 781] 376-3000 ? fax [781] 376-3100 ? sales@ skyworksinc.com ? www.skyworksinc.com 6 august 13, 2015 ? skyworks prop rietary information ? products and product information are s ubject to change without notic e ? 203034f table 6. sky66109-11 mode control logic (note 1) (vcc1 = vcc2 = 3.0 v, t a = +25 ? c) mode description cps (pin 18) csd (pin 17) ctx (pin 20) typical current consumption 0 all off (sleep mode) (note 2) x 0 x 0.1 a 1 receive bypass mode 0 1 0 250 a 2 receive lna mode 1 1 0 5 ma 4 transmit mode x 1 1 30 ma n ote 1 : 0 = 0 v. 1 = +3.0 v. x = dont care (must be either 0 v or vcc voltage). any state other than described in this table p laces the switch into an undefined state. an undefined state will not damage the device. n ote 2: remove evb pulldown resistors to achieve sp ecified sleep current with ctx or cps high. table 7. sky66109-11 antenna enable logic (vcc1 = vcc2 = 3.0 v, t a = +25 ? c) description cps (pin 18) csd (pin 17) ctx (pin 20) ant_sel (pin 14) ant1 port enabled x x x 0 ant2 port enabled x x x 1 n ote : 0 = 0 v. 1 = +3.0 v. x = dont care. any state other than described in this table places the switch into an undefined s tate. an undefined state will not damage the device.
data sheet ? sky66109-11: zigbee/smart energy fem skyworks solutions, inc. ? phone [ 781] 376-3000 ? fax [781] 376-3100 ? sales@ skyworksinc.com ? www.skyworksinc.com 203034f ? skyworks proprietary information ? products and product in formation are subject to cha nge without notice ? aug ust 13, 2015 7 evaluation board description the sky66109-11 evaluation board is used to test the performance of the sky66109-11 fem. the board is optimized for evaluation, experimentation, and investigation with an 802.15.4 signal source. the design and layout can be quickly and easily transferred into a production design. an evaluation board schematic diagram is provided in figure 4. a reference design schematic is provided in figure 5. table 8 describes the pins on the power and control i/o header (j5). table 9 provides the bill of materials (bom) list for evaluation board components. the evaluation board is shown in figure 6. evaluation board setup procedure 1. connect j1, j2, j3, and j4 to 50 instruments. terminate all unused ports (if applicable) with 50 . 2. connect the supply ground to pins 19 and 20 of j5. 3. connect 3.0 v to pins 15 and 16 of j5. 4. connect 3.0 v to pins 3 and 4 of j5. note: pins 7 and 8 of j5 are left open. note : by following the logic in table 6, the required rf path is selected. refer to table 7 for antenna port control. 5. monitor the 2.5 g hz amplifier transmit performance by applying an rf signal to j3 and monitoring the output power on j1 (ant1) or j2 (ant2). caution : care should be taken not to overdrive the amplifier by applying too much rf on the input to the device. a suitable starting input power would be ?0 dbm. 6. monitor the 2.5 g hz amplifier receive performance by applying an rf signal to j1 (ant1) or j2 (ant2) and monitoring the output signal on j3. package dimensions the pcb layout footprint for the sky66109-11 is provided in figure 7. typical part markings are shown in figure 8. package dimensions for the 20-pin mcm are shown in figure 9, and tape and reel dimensions are provided in figure 10. package and handling information since the device package is sensitive to moisture absorption, it is baked and vacuum packed before shipping. instructions on the shipping container label regarding exposure to moisture after the container seal is broken must be followed. otherwise, problems related to moisture absorption may occur when the part is subjected to high temperature during solder assembly. the sky66109-11 is rated to moisture sensitivity level 3 (msl3) at 240 ? c. it can be used for lead or lead-free soldering. for additional information, refer to the skyworks application note, pcb design and smt assembly/rework guidelines for mcm-l packages , document number 101752. care must be taken when attaching this product, whether it is done manually or in a production solder reflow environment. production quantities of this product are shipped in a standard tape and reel format.
data sheet ? sky66109-11: zigbee/smart energy fem skyworks solutions, inc. ? phone [ 781] 376-3000 ? fax [781] 376-3100 ? sales@ skyworksinc.com ? www.skyworksinc.com 8 august 13, 2015 ? skyworks prop rietary information ? products and product information are s ubject to change without notic e ? 203034f v cc vdd vb_out vb_in c tx c p s cs d v cc 2 ant s el 2 4 6 8 10 12 14 1 6 18 20 1 3 5 7 9 11 13 15 17 1 9 vdd vb_out vb_in c 1 2.2 f c 2 2.2 f v cc j5 v cc c 4 100 nf c 8 10 pf c tx r3 100k r1 100k r2 100k c p s cs d c 3 100 nf c 7 10 pf r4 100k v cc 2 ant s el j1 s m a j2 s ma vb_in vb_out c 5 10 pf c6 10 pf j4 s ma j3 s ma un_bal rf_gnd bal_pt 1 2 3 n/ c gnd bal_pt 6 5 4 un_bal rf_gnd bal_pt 1 2 3 n/ c gnd bal_pt 6 5 4 u3 u2 gnd txp txn vb_out rxp rxn 1 2 3 4 5 6 1 6 15 14 13 12 11 v cc 2 gnd ant_ s el gnd ant1 gnd 7 8 9 10 vb_in gnd gnd ant2 c tx v cc 1 c p s cs d 20 1 9 18 17 pad 21 s ky 66 10 9 -11 u1 y030 9 figure 4. sky66109-11 evaluation board schematic
data sheet ? sky66109-11: zigbee/smart energy fem skyworks solutions, inc. ? phone [ 781] 376-3000 ? fax [781] 376-3100 ? sales@ skyworksinc.com ? www.skyworksinc.com 203034f ? skyworks proprietary information ? products and product in formation are subject to cha nge without notice ? aug ust 13, 2015 9 v cc c 4 100 nf c 8 10 pf c tx c p s cs d c 3 100 nf c 7 10 pf v cc ant s el ant1 ant2 vb_in vb_out gnd txp txn vb_out rxp rxn 1 2 3 4 5 6 1 6 15 14 13 12 11 v cc 2 gnd ant_ s el gnd ant1 gnd 7 8 9 10 vb_in gnd gnd ant2 c tx v cc 1 c p s cs d 20 1 9 18 17 pad 21 s ky 66 10 9 -11 u1 y0315 txp txn l2 rxp rxn l1 figure 5. sky66109-11 reference design schematic table 8. power and analog i/o header: j5, 10x2 pin pin name description recommended setting 1, 2, 15 vcc supply voltage g eneral purpose vcc provided as the main power supply 3, 4, 9, 11, 13, 17 vdd digital supply voltage connect to separate power supply voltage 5, 6 vb_out bias output C 7, 8 vb_in bias voltage input no connect 16 vcc2 supply voltage g eneral purpose vcc provided as the main power supply 10 ctx control see tables 6 and 7 12 cps control 14 csd control 18 ant_sel control 19, 20 g nd g round g eneral purpose ground
data sheet ? sky66109-11: zigbee/smart energy fem skyworks solutions, inc. ? phone [ 781] 376-3000 ? fax [781] 376-3100 ? sales@ skyworksinc.com ? www.skyworksinc.com 10 august 13, 2015 ? skyworks prop rietary information ? produc ts and product information are subject to change without noti ce ? 203034f table 9. sky66109-11 evaluation board bill of materials (bom) component value size manufacturer manufacturer part number characteristics c1, c2 2.2 f 0805 murata g rm21br71a225ka01l ceramic capacitor, 2.2 f, 10v, 10%, x7r 0805 c3, c4 100 nf 0402 murata g rm155r71c104ka88d monolithic ceramic c5, c6, c7, c8 10 pf 0402 murata g rm1555c1h100jz01 multilayer ceramic j1, j2, j3, j4 sma end launch johnson components 142-0701-851 sma end launch straight jack receptacle C tab contact j5 10x2 100 mil samtec tsw-110-07- g -d 100 mil header r1, r2, r3, r4 100 k 0402 panasonic erj2 g ej104 thick film chip resistor u1 C 3 x 4 mm mcm skyworks solutions, inc. sky66109-11 2.4 g hz zigbee fem with differential transmit/receive u2, u3 C 2 x 1.25 mm tdk hhm1521 multilayer 2.4 g hz chip baluns n ote : schematic and bom have been designed to op timize performance in 802.11a/n applications. y1727 figure 6. sky66109-11 evaluation board
data sheet ? sky66109-11: zigbee/smart energy fem skyworks solutions, inc. ? phone [ 781] 376-3000 ? fax [781] 376-3100 ? sales@ skyworksinc.com ? www.skyworksinc.com 203034f ? skyworks proprietary information ? products and product in formation are subject to cha nge without notice ? aug ust 13, 2015 11 4.3 mm 20x 0.5 6 mm 3.3 mm 20x 0.25 mm 4x 0.5 9 mm 2x 0.4375 mm 2x 0.513 mm s tencil aperture top view s tencil aperture s ize for center ground pad s hould be 80% to 100% (by area) of the s older ma s k opening 0.5 mm pitch package outline pin 20 pin 1 indicator 0.20 x 45 pin 1 0.5 mm pitch package outline pin 20 pin 1 indicator 0.20 x 45 pin 1 s older ma s k opening top view 4.4 mm 20x 0. 66 mm 20x 0.35 mm 4.3 mm package outline 0.5 mm pitch pin 20 pin 1 metallization top view 3.4 mm 2x 0.5 9 mm opening s ize of 6 0% to 100% of expo s ed center opening s hown 2.1045 mm 14x 0.5 6 mm 14x 0.25 mm 3.3 mm thermal via array ? 0.3 mm on 0. 6 mm pitch improve s thermal performance y0317 note: thermal vias should be resin ?led and capped in accordance with ipc-4761 type vii vias. recommended cu thickness is 30 to 35 ?. figure 7. pcb layout footprint pin 1 indicator note: line s 1, 2, and 3 have a maximum of 7 character s line 1 = part number and ver s ion line 2 = lot number line 3 = year-week- c ountry c ode (mx) y152 9 line 1 line 2 line 3 figure 8. typical part markings
data sheet ? sky66109-11: zigbee/smart energy fem skyworks solutions, inc. ? phone [ 781] 376-3000 ? fax [781] 376-3100 ? sales@ skyworksinc.com ? www.skyworksinc.com 12 august 13, 2015 ? skyworks prop rietary information ? produc ts and product information are subject to change without noti ce ? 203034f 4b pin 1 indicator c 3 top view 0.15 a b c top a 0.1 0.95 0.1 side view bottom view 20x smt pad 4x 0.25 4x 0.75 12x 1.4 see detail b 4x 0.25 4x 0.75 4x 1.25 8x 1.9 0.577 0.577 0 0.1 m a b c solder mask opening 0.2 a b c 0 a pin 20 pin 1 indicator see detail c pin 1 1.026 5x r0.05 max 1.18 solder mask edges 0.2 x 45 detail c pad scale: full 1x this rotation 0.875 detail b pad scale: full 1x this rotation 1.18 solder mask edges 4x r0.05 max (0.1) 0.31 0.1 0.35 0.05 0.25 0.05 (0.05) metal pad edge detail a pad scale: 2x 4x this rotation 4x rotated 180 notes (unless otherwise speci?d): 1. dimensions and tolerances are in accordance with asme y14.5m?994. 2. dimensions are in millimeters. y0308 figure 9. sky66109-11 20-pin mcm package dimensions
data sheet ? sky66109-11: zigbee/smart energy fem skyworks solutions, inc. ? phone [ 781] 376-3000 ? fax [781] 376-3100 ? sales@ skyworksinc.com ? www.skyworksinc.com 203034f ? skyworks proprietary information ? products and product in formation are subject to cha nge without notice ? aug ust 13, 2015 13 8.00 3.40 4.40 1.10 2.00 0.05 (note 3) 0.30 0.05 r0.3 max. 4.00 (note 1) 0.12 r0.25 0.12 ? 1.50 min. ? 1.5 +0.1/C0.0 12.0 0.30 1.75 0.10 pin 1 indicator 5.50 0.05 (note 3) a notes: 1. 10 sprocket hole pitch cumulative tolerance 0.2. 2. camber in compliance with eia 481. 3. pocket position relative to sprocket hole measured as true position of pocket, not pocket hole. 4. all measurements are in millimeters. a a s2742 figure 10. sky66109-11 tape and reel dimensions
data sheet ? sky66109-11: zigbee/smart energy fem skyworks solutions, inc. ? phone [ 781] 376-3000 ? fax [781] 376-3100 ? sales@ skyworksinc.com ? www.skyworksinc.com 14 august 13, 2015 ? skyworks prop rietary information ? produc ts and product information are subject to change without noti ce ? 203034f ordering information model name manufacturing part number evaluation board part number sky66109-11 sky66109-11-r sky66109-11-ek1 copyright ? 2013-2015 skyworks solutions, inc. all rights reserved. information in this document is provided in connection with skyw orks solutions, inc. (skyworks) products or services. these m aterials, including the information co ntained herein, are provided by skyworks as a service to its customers and may be used for info rmational purposes only by the cu stomer. skyworks assumes no res ponsibility for errors or omissions in these materials or the information contained herein. skyworks may change its documentat ion, products, services, specific ations or product descriptions at any time, without notice. skyworks makes no commitment to update the materials or information and shall have no responsi bility whatsoever for conflicts, incompatibilities, or other diff iculties arising from any future changes. no license, whether express, implied, by es toppel or otherwise, is granted to any in tellectual property rights by this document . skyworks assumes no liability for any materials, products or information provided hereunder, including the sale, distribution, re production or use of skyworks products, information or mate rials, except as may be provided in skyworks terms and conditions of sale. the materials, products and information are pr ovided as is without warranty of any ki nd, whether express, implied, statutory, or otherwise, includin g fitness for a particular purpose or use, merchantability, performance, quality or non-infrin g ement of any intellectual property ri g ht; all such warranties are hereby expressly disclaimed. skyworks does not warrant the accuracy or completeness of the information, text, g raphics or other items contained within these ma terials. skyworks shall not be liable for any dama g es, includin g but not limited to any special, indirect, incidental, statutory, or consequential dama g es, includin g without limitation, lost revenues or lost profits that may result from the use of the materials or information, wheth er or not the recipient of mat erials has been advised of the possibility of such dama g e. skyworks products are no t intended for use in medical, lifesaving or life-su staining applications, or other equipment in which the failure of the skyworks products could lead to personal injury, death, physical or environmental damage. skyw orks customers using or selli ng skyworks products for use in such applications do so at their own risk and agree to fully indemnify skyworks for any damages resulting from such improper use or sale. customers are responsible for their products and applications us ing skyworks products , which may deviate from published specifi cations as a result of design de fects, errors, or operation of products outside of published pa rameters or design specifications. customers sh ould include design and operating safeguards to minimize these and other risks. skyworks assumes no liability for applications assistance, customer product de sign, or damage to any equipment resulting from the use of skyw orks products outsid e of stated published specifications or parameters. skyworks and the skyworks symbol are trademarks or registered trad emarks of skyworks solutions, inc., in the united states and other countries. third-party brands and names are for identification purposes only, and are the pr operty of their respective owners. additi onal information, including relevant terms and conditions, posted at www.skyw orksinc.com, are incorporated by reference.

▲Up To Search▲

Price & Availability of SKY66109-11-15

	To Download SKY66109-11-15 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .